Silver Eagle ManufacturingCall
Manuals / SYSCO Parts Book 39151 Final.docx

SYSCO

SYSCO Parts Book 39151 Final.docx

Parts
74

Assemblies

2 FIFTH WHEEL

Parts

74 of 74 parts
ItemPart No.DescriptionSectionQty
—15594Kit, Eye&Shank, Hex Nut, W/Sfty Wire & Rnd Bush2 FIFTH WHEEL—
—22112Installation, Limit Cables 16", 86-102Dl VAII2 FIFTH WHEEL—
—24934GSide Channel, 84" Dl, VAII, Galv2 FIFTH WHEEL—
—31042-0090° 1/8”MNPT x 1/4”TBG2 FIFTH WHEEL—
—31083-12Drain - Petcock2 FIFTH WHEEL—
—31083-23Control Box Only (without lid)2 FIFTH WHEEL—
—31083-28Control Box Lid w/Screws and Gasket2 FIFTH WHEEL—
—31084-01Bulkhead Fitting2 FIFTH WHEEL—
—31084-02Bulkhead Fitting2 FIFTH WHEEL—
—31084-10Control Box Flow Sensing Switch - In-Line. ThermALERT ready. Color Gray. Replaces 31084-03 which cannot be used on2 FIFTH WHEEL—
—31114-00Steel 1/8” Bulkhead/Check Valve2 FIFTH WHEEL—
—31114-00Control Box Bulkhead/Check Valve2 FIFTH WHEEL—
—31163-001/4”TBG Union Tee2 FIFTH WHEEL—
—31182-70Wiring Harness2 FIFTH WHEEL—
—31222-001/4” Cable Choke Seal2 FIFTH WHEEL—
—31272-01MTIS Attention Label, 10 pack2 FIFTH WHEEL—
—31282-01MTIS 1-800 Label, 10 pack2 FIFTH WHEEL—
—31314-2110.50”2 FIFTH WHEEL—
—31317-033.50”2 FIFTH WHEEL—
—31364-0011.50”2 FIFTH WHEEL—
—31373-0017.00”2 FIFTH WHEEL—
—31482-0112-R Press Plug O-Ring (328), 3 pack2 FIFTH WHEEL—
—31492-01O-Ring (small 020), 10 pack2 FIFTH WHEEL—
—31924-03Dana/Eaton V3 and V42 FIFTH WHEEL—
—31935-03Ingersol F22, Hendrickson HN2 FIFTH WHEEL—
—31955-03Holland ProPar2 FIFTH WHEEL—
—31964-03Meritor TN/TQ, HN, D22 Hollow2 FIFTH WHEEL—
—31982-01Small Parts Assortment. Contains: Pressure Protection Valve, 1/4” NPT x 1/4” TBG 90° Fitting, 3/8” Hex Nipple2 FIFTH WHEEL—
—32184-01ATP Press Plug Kit with O-Ring2 FIFTH WHEEL—
—32184-01A2.75” Press Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TP, TB, WP, Hendrickson HP (After 2002)2 FIFTH WHEEL—
—32202-01A1.75” Press Plug Kit with O-Ring2 FIFTH WHEEL—
—32202-01A1.75” Press Plug Kit with O-Ring. Includes adhesive. Used in Meritor TN/TQ, RN/RQ, Hendrickson HN2 FIFTH WHEEL—
—32251-01O-Ring (large 324), 3 pack2 FIFTH WHEEL—
—32261-00MTIS Light Label (Single Pack)2 FIFTH WHEEL—
—32271-01Press Plug Kit with O-Ring. Includes Adhesive. Used in Sudisa 9M Axle2 FIFTH WHEEL—
—32321-01A2.75” Press Plug Kit with O-Ring. Includes Adhesive. Used in Holland ProPar2 FIFTH WHEEL—
—32321-01AProPar Press Plug Kit with O-Ring2 FIFTH WHEEL—
—32342-01A1.904” Press Plug Kit with O-Ring. Includes Adhesive. Used in Holland Trade2 FIFTH WHEEL—
—32342-01A1.86” Holland Trade Press Plug Kit2 FIFTH WHEEL—
—32352-011.86” Press Plug O-Ring (223), 3 pack2 FIFTH WHEEL—
—32375-03Holland Trade2 FIFTH WHEEL—
—32382-01A2.95” Press Plug Kit with O-Ring used in Meritor TB Axles with Large Spindle Bore2 FIFTH WHEEL—
—32382-01A2.95” Press Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TB Axles with Large Spindle Bore2 FIFTH WHEEL—
—32405-03Meritor TB (2.95”)2 FIFTH WHEEL—
—32472-01A2.50” Hendrickson HP Press Plug Kit2 FIFTH WHEEL—
—32473-01A2.50” Press Plug Kit with O-Ring. Includes Adhesive. Used in Dana P22, Hendrickson HP (Pre 2002)2 FIFTH WHEEL—
—32595-03Sudisa 12-R2 FIFTH WHEEL—
—32601-01A2.25” Press Plug Kit with O-Ring. Includes Adhesive. Used in Sudisa 12R2 FIFTH WHEEL—
—32611-01A1.50” Press Plug Kit with O-Ring. Includes adhesive. Used in Sudisa 11M2 FIFTH WHEEL—
—32645-03Sudisa 11-M2 FIFTH WHEEL—
—32701-01A1.50” Press Plug Kit with O-Ring. Includes adhesive. Used in Ingersol F222 FIFTH WHEEL—
—32815-03Dana P22, Hendrickson HP2 FIFTH WHEEL—
—36804Fastener Kit, Side Channel Replacement, VAII2 FIFTH WHEEL—
—39727DWB KIT 11 X 84 SYSCO, GALVANIZED CS2 FIFTH WHEEL—
—39729DWB KIT 11 X 84 SYSCO, GALVANIZED RS2 FIFTH WHEEL—
—51011-01Driver - Holland ProPar2 FIFTH WHEEL—
—51011-02Driver - Meritor TN/TQ, RN/RQ, Hendrickson HN, Dana/ Eaton D22 Hollow Spindle2 FIFTH WHEEL—
—51011-03Driver - Sudisa 12-R2 FIFTH WHEEL—
—51011-04Driver - Sudisa 11-M2 FIFTH WHEEL—
—51011-05Driver - Holland Trade2 FIFTH WHEEL—
—51011-06Driver - Meritor TP/TB2 FIFTH WHEEL—
—51011-07Driver - Meritor WP2 FIFTH WHEEL—
—51011-08Driver - Ingersol F222 FIFTH WHEEL—
—51011-09Driver - Sudisa 9-M2 FIFTH WHEEL—
—51011-10Drive Handle2 FIFTH WHEEL—
—51011-11Driver - Hendrickson ProPar (2.50”)2 FIFTH WHEEL—
—51011-13Driver - Dana P222 FIFTH WHEEL—
—51011-14Driver - Meritor TB (2.95” Oversized Bore)2 FIFTH WHEEL—
—51031-00System Pressure Test Gauge. Replaces 81014-002 FIFTH WHEEL—
—61021-01APress Plug Kit with O-Ring. Includes Adhesive. Used in Meritor TL Axles2 FIFTH WHEEL—
—61051-00Driver - Meritor TL2 FIFTH WHEEL—
—81044-00Slide Hammer - Removes axle plugs and press2 FIFTH WHEEL—
—81044-00Press Plug Remover. Attaches to 81044-002 FIFTH WHEEL—
—81044-01Welsh Plug Removal Spear. Attaches to 81044-002 FIFTH WHEEL—

Service Procedures

1. UNCOUPLING · COUPLING

Pull dolly slowly out from under the trailer.

1. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Set brakes on unit.

1. Drawbar Eye Inspection · COUPLING

Drive Handle and Drivers (for installation of Press Plugs into Axle Spindles)

2. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Remove safety wire on shank nut.

2. UNCOUPLING · COUPLING

If the handle will not pull outward when the vehicle

3. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Remove shank nut and shank washer.

4. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Use forklift for hostler to pull against drawbar

5. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Lubricate the shank of the new drawbar eye with rubber lubricant or soapy

6. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

After the drawbar eye is in place, clean the threads on the shank and coat the

6. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Set the brakes on the trailer. Use a forklift or hostler to push against the

7. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Install the shank washer and thread the shank nut onto the shank.

8. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Tighten the shank nut until three to four threads remain exposed inside the nut.

9. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Install a Silver Eagle safety wire on the shank nut to prevent it from backing off.

10. DRAWBAR EYE REMOVAL AND INSTALLATION PROCEDURE · REMOVAL

Periodically check the tightness of the shank nut and adjust as necessary.

← All manualsContact parts team →